Underfloor Heating

Underfloor Heating based in Stourbridge

Covering the West Midlands including Birmingham, Dudley and Wolverhampton

If you're based in the West Midlands and interested in underfloor heating, then RJM Multi Trade are the right team for you. 

How does underfloor heating work? 

The clever thing about underfloor heating is that it works by effectively turning your floor into a large, comfortably warm and cosy radiator. Once the temperature of the floor rises above the ambient temperature of the air, the heat is spread evenly across the surface of the floor, creating an inviting warmth that should leave no cold spots, anywhere.

Even more clever than this, the surface area of a floor is much larger than a conventional radiator, which means it doesn’t have to be heated to the same high temperature to provide you with sufficiently comfortable heat; making it more energy efficient.

There are two types of under floor heating:

One of them features water that is fed around pipes in a sub-floor (wet) and the other uses electric wires or matting that are either set inside concrete screed or tiles, or just simply installed under your floors (dry).

Is underfloor heating more efficient?

How much underfloor heating costs to operate in the long run will mostly depend upon the fuel you use, the cost of that fuel and the overall efficiency of the system – especially the quality of the boiler and level of insulation in your building. These are far more important factors than the minimal cost differences between underfloor and other types of central heating.

It is essential that your floor is suitably insulated for your UFH to have an effective and efficient output and the higher the quality of the insulation, the greater the impact on the overall running costs. Indeed, quality insulation is a big contributing factor to the increased initial costs of UFH installations, it’s worth it in the long run. 

Warm water or electric underfloor heating? 

Electric underfloor heating is generally believed to be slightly quicker, and therefore normally cheaper, to install than the warm water alternative, but both can be used to heat your entire house or just individual rooms – for example only the ground floor or perhaps just in the bathroom to take that often unwelcome chill off the tiles. 

If you are undertaking a retrofit installation it is perhaps best to use an electric system because they tend to be thinner and more manageable than warm water systems. In fact, for this very reason, electric or ‘dry’ systems are normally the primary option for renovators looking to install underfloor heating. 

Available in differing styles, electric systems can come in the form of heating mats which can be rolled out to cover large areas, or, for those smaller more awkward spaces, you can purchase versions that consist of more loose fitting flexible wiring. 

Though slightly cheaper to buy and install than the warm water alternative, from a more long term point of view, electrical systems are thought to be more expensive to run and are not recommended for heating large areas. 

Does the floor covering matter? 

Wood – There are generally two types of wooden floor. These are engineered timber, like laminates and solid timber flooring. When it comes to underfloor heating in screed we would recommend that the best method of installation is to float the flooring on top of a 2-3mm polythene foam that allows the wood to lay flat and expand and contract naturally.      

Remember that solid wood floors have a tendency to move more than laminate. You can help to prevent this by leaving your wood to acclimatise to the room for a few days before laying and ensuring that the screed and the building itself is thoroughly dry before installation.

It is also a good idea to bear in mind that wood is not the best conductor of heat. Heavy, dense wood grains help to give you a better heat output, whereas light woods are less effective. The very worst thing you can do to waste your time, energy and money is to install underfloor heating under wood and then cover your floor with lots of rugs that make it harder for the heat to penetrate the floor.

Carpet – If you have ever been in a makeshift recording studio, or lived in a flat with really thin walls and ceilings, you will already know that carpet acts as a great insulator (not only of noise, but also of heat), meaning that the thicker the carpet, the lower the heat output of your underfloor heating.

It is generally accepted throughout the industry that your carpet and underlay should not exceed a combined tog (thermal resistance) rating of 1.5 – the higher the tog, the more pipes and cables you’ll need to install to compensate.

Flags, Slate & Marble – Probably the very best suited to underfloor heating, stone and stone flags have a high thermal mass that makes them great heat conductors that achieve a temperature that you will find extremely pleasurable underfoot.

Sawn or cut flagstones with a bed of 25-50mm (1” – 2”) are best laid in an adhesive or a bedding with a special additive that will allow the floor to expand and contract. You can also use random depth flagstones with your underfloor heating too, but remember that their large thermal mass and differing depths may slow down your underfloor heating response time and it’s always best to use a flexible grout with stones too.

Ceramic – Great for use with underfloor heating because of their relatively high thermal mass, ceramic or terracotta tiles are excellent conductors. They should be laid with an appropriate tile adhesive and grout that is compatible with underfloor heating and that allows for movement; ensuring that you have switched off the system before installation.

PVC Tiles / Linoleum – Glue the tiles with a flexible adhesive that won’t degrade with the heat. Something like Styccobond is good. Ensure that the underfloor heating is turned off for a good 48 hours before and after installation and lay the tiles directly onto the screed.

Will I need a special boiler for underfloor heating?

How you design warm water underfloor heating does need to take into account the boiler that you are using and the sophistication of the built in controls. It goes without saying that the more efficient the boiler, the more efficient the system will be.

If you have a gas powered system, a condensing boiler is more than worth the investment as it will operate at its most efficient with a low temperature system like underfloor heating and it is also good to remember that underfloor heating can also be used with renewable heat sources like heat pumps and solar panels.

Click below to get yourself a quote